I use a 5600g on b450 ITX board and 4x 8GB Seagate drives and see about 35W idle and about 40W average. It used to be 45W because I was forced to use a GPU in addition to a 3600 to boot (even though its headless, just a bad bios setup that I can’t fix) and getting a CPU with graphics dropped my idle consumption quite a bit. I suspect the extra wattage for your machine is probably the bigger motherboard and the less efficient CPU.

It is possible to get the machine part down into single digits wattage and then about 5W a drive is the floor without spinning them down, so the minimum you could likely see with a much less powerful CPU is about 30-35W.

Make sure none of the exceptions are ticked and the Minimum number of articles to keep per feed is also 25 or below. Then its up to the cron when that runs so you might have to manually purge it and optimise the database to see what it will actually keep.

I can’t say I have ever worried about it, been running FreshRSS for years and it seems to keep its database size in check fairly well and the defaults have worked fine for me and it rarely gets above 100MB. So I know it “loosely” works in that old articles are absolutely getting purged in time but have no idea how strictly it follows these rules.

The DMZ for the ISPs router forward to the second router, then everything that hits your outside IP will be forwarded to router 2. Then on Router 2 you open the ports for your service and forward to the internal machine. That should all work fine.

Its quite complicated to setup as well, just went through the instructions and its a long way from just add to docker and run unfortunately. Would be nice to be able to just get a runner in the same or different docker and it just works easily without a lot of manual setup in Linux of directories and users and pipes etc.

I did the same move from contabo to Netcup. Contabo I had all sorts of weird bandwidth limiting problems that I couldn’t explain and which the continued to deny they were throttling. Netcup worked perfectly.

The problem is the information asymmetry, there is always another person for a fraudulent company to exploit due to a dysfunctionally expensive court system. Its why we need market level regulations and public institutions that recover peoples money and fine the organisations for their breaches. This sort of thing works a lot better in the EU than in the US due to the sales laws, the ability to return within 2 weeks, default warranty on goods out to 12 months and expectations of goods to be as advertised forced onto the retailers. They work, they need more enforcement from regulatory bodies but retailers do follow them for the most part and quickly change tune when you go to take legal action when they don’t because courts know these laws inside and out.

Mine are only 25k hours or so, around 3 years. My prior set of disks had a single failure at 6 years but I replaced them all and went to bigger capacity. There is also the power saving aspect of going down to 2 drives as well, it definitely saves some power not spinning 4 extra drives all the time.

I sub to channels and use Youtubes recommendations and new for you to find additional channels etc but I don’t watch them I use Metube and a browser plugin and download the videos to a directory. I don’t get all the privacy but I also am not giving them much watch data and I can avoid the ads.

AMD has unfortunately a long history of abandoning products before its reasonable on its graphics division. Its not really acceptable, up until earlier this year my NAS/server was running a 3600 and its only for power saving purposes I changed that as its still a very workable CPU in that role.

It really depends on the project. Some of them take breaking changes seriously and don’t do them and auto migrate and others will throw them out on “minor” number releases and there might be a lot of breaking changes but you only run into one that impacts you occasionally. I typically don’t want containers that are going to be a lot of work to keep up to date so I jettison projects that have unreliable releases for whatever reason and if they put out a breaking change its a good time to re evaluate whether I want that container at all and look at alternatives.

So no its not safe, but depending on the project it actually can be.

Ideally for your router you want something that runs an open source firmware (OpenWRT, DD-WRT, OPNSense, FreshTomato). Its better because you get a completely unlocked everything you need system with security patches for the hardware’s true lifetime. Every router company stops with the security updates after a few years and then at some point it becomes part of a bot net or one of this mass hack events. Its best not to play in that game and instead run some open source firmware from the outset.

The best way to start is to look at the website for openwrt.org and use their filtering to find a device that supports your needs (at least 5 LAN ethernet ports I guess and some wifi but AC sounds like it will do). The other option is a more typical 4 LAN port router which will give you a lot more options and then add a switch to that, doesn’t sound like you care too much about it being managed or >1gbps so they are also dirt cheap.

Metube is great and also has some browser plugins as well so it’s as simple as right click and send to metube on a YouTube link. Wish there was one for android too but alas not yet that I have seen.

I don’t think modern Raspberry pi’s make much sense unless you are using GPIOs or really need the low power consumption. The 3 and the 4 were OK price wise but the pi 5 is quite close to all these N100 mini computers and they are a lot more performance and expansion compared to a raspberry pi 5 and still quite low power.

Either a Topton or similar N100 based machine or a mini PC second hand is the way to go at the ~$100 mark. The mini PC will be faster and probably more expandable and cheaper but also more power consumption.

Another possibility for cheap VPS is Contabo they are quite good value. Netcup is good value as well.

I used Invidious for about a year and it was a constant string of bugs. Every release was a risk and quite often updates would get lost or the database would explode in size and consume all the drive space. Its not a project I currently use or recommend until it stabilises.

Hugo? As in your generated site or you have some sort of service that costs hugo that generates and deploys your site or something else?

It has been slowly improving. It used to be a lot worse but I have a lot less issues with it now than I did before all the changes. Its not the fastest best way to do anything, there are better calendar, file sync, email etc etc applications out there in every category that run better but its also quite an easy way to make a lot of things happen.

The new Linuxserver.io docker image at the very least has solved the annoying update cycle NextCloud has and seems to have fixed the need to do that every few months. I haven’t ever had it die but I don’t push it hard and I keep the plugins to a minimum because I just don’t trust it and it doesn’t run all that well.

Even the main search engines don’t index the entire internet of content these days and their databases are truly massive already. Writing a basic web crawler to produce a search index isn’t all that hard (I used to do it as a programming exercise for applicants) but dealing with the volume of data of the entire internet and storing it to produce a worthwhile search engine however is just not feasible on home hardware, it would be TB’s at least. It wouldn’t just be a little worse it would dramatically worse unless you put substantial resources to it including enormous amounts of network bandwidth which would have your ISP questioning your “unlimited 1 gbps fibre” contract. It would probably take years to get decent and always be many months out of date at best.

Doesn’t seem practical to try to self host based on the need to download and index every single page of the internet its a truly massive scale problem.